2019
Vol 4, No 1 (2019): Integration of Block Chain and Digital Grid Routers for Load Balancing and Bidirectional Power Flow in Microgrid
Abstract:-In response to the situation of increasing energy demand day by day it is necessary to fulfill the requirement of consumers. The power generated by the base load plants is not sufficient to meet the demand. Therefore it is necessary to introduce the distributed generation to meet the demand. The government is promoting renewable energies such as solar or wind power plant installation because of green energy. The renewable-energy penetration and controlling is challenging task in centralized power distribution. To find the solution to this problem is essential. To overcome this problem a smart grid or micro grid concept was introduced which is one of the principal concerns of the scientific community is the energy transition and energy efficiency. In micro grid the power flow and exchange is done with group of people in a particular areas. It would optimize the energy consumption by setting consumption patterns, adapted to a specific situation, taking into account different parameters like the price, the user preferences, or the parameters of the appliances of the house. Thus a numerical management is needed to load balancing and distribution of energy. A block chain is a distributed, decentralized transaction ledger, which is owned, maintained and updated by each user. It carries peer-to-peer energy exchanges among citizens of a same microgrid, without a central control body, based on smart contracts. The digital grid router solves the problems of different renewable source integration in smart grid. . The Digital Grid divides power systems when frequency is synchronized into various sizes. Each small grid is connected asynchronously with a
digital grid router (DGR). This paper focuses on load balancing with
peer to peer transactions in microgrid using block chain and
bidirectional power flow using digital grid routers.
Vol 4, No 1 (2019): A Novel Distribution System Planning of Distributed Generation and Bi-directional Power Flow Using Digital Grid Router
Authors:-Prakash Kerur, Dr. R.L. Chakrasali
Abstract:- Solar energy is inexhaustible, available abundant in nature and free from pollution. The solar photovoltaic (PV) systems are a perfect solution for power requirement urban residential areas since the system is noiseless. The main problem with solar energy is its intermittency. However, sometimes during clear days the solar panels generate surplus power beyond the needs. At these times, the surplus power is exported into the main utility grid. With increase of renewable energy sources causes various problems of grid integration to export the surplus power. The concept of digital grid (DG) and bi-directional smart meters are the solution for these problems. The digital grid†where a wide-area synchronized power system is sub divided into smaller or medium sized power systems. Subdivided grids called “digital grid cells†are connected together asynchronously via “digital grid routersâ€. The DGR is a multi-terminal AC/DC/AC power conversion device. In order to construct a DG, bi-directional power flow and asynchronous interconnection of many distributed solar roof tops. If the solar PV panel produces surplus power, then it has to be supplied to the grid and the exported surplus power must be accounted. The smart energy meter has to account for imported power from the grid to consumer system and the exported power from the consumer system to grid. In this paper Digital grid router(DGR) and smart meter combination are discussed.
2018
Vol 3, No 1&2 (2018): Power Flow Control and Communication in Autonomous Distribution System using Tie-Set Graph Theory and Johnson’s Algorith
Authors:-Prakash Kerur, R.L.Chakrasali
Abstract:-Micro grid distribution system planning is important to ensure that the growing need of electricity is met by the distributors. Planning starts at customer level, Individual power producers (IPPs) are the part of the power management system, as low power generated by the IPPs should reach the consumer through the shortest path in order to reduce the feeder line losses in low voltage distribution networks. Therefore, proper planning of the distribution system is very important to maintain continuity of power. While Planning Distribution System (DSP) the concept of graph theory can be used such that it involves selection of all possible paths through the graph between each pair of vertices. It compares the paths that exist between each pair of vertices until an optimal shortest path between two vertices is achieved. In this work selection of optimal shortest path is obtained using Johnson’s Algorithm. Several optimization techniques have been implemented to solve the problem of identification of shortest path. The work presented in this paper is  yet another approach to address the same issue. To validate the proposed method, it is implemented on IEEE 8 bus system and simulation carried out using MAT LAB with results obtained for bidirectional power flow.
2017
Vol 2, No 3 (2017): Automatic Energy Meter Reading and Theft Detection
Authors:Â Sandip S. Rathod, Ganesh D. Shingade, Amol P. Chopade
Abstract: Electricity has become one of the basic requirements for human life, being widely used for domestic, industrial and agricultural purposes. In our work, we propose a digital energy meter which measures the energy consumption and the energy measured is transmitted periodically to the remote server or user or electricity board so that energy consumption can be monitored from remote end. Additionally an important concept used here is the IoT (Internet of Things). It objective is to generate bill automatically by checking the electricity unit’s consumption in a house and in a way to reduce the manual labor. The calculations are performed automatically and the bill is updated on the internet by using a network of Internet of Things Iot is an emerging system with unique identifiers and having the ability to transfer data over a network without human-to-human or human-to-computer interaction. Here using IoT the meter readings are uploaded into our specific web page for remote monitoring.
Vol 2, No 3 (2017): A Lightweight and Secure Cryptography for Communication between Smart Meters and Grids using ARM cortex M0 Microcontroll
Authors:Â R.Stephygraph, K.Ganesan
Abstract:Â In this paper data transmission with secure option using wireless technology the Smart Meters send the energy consumption unit and peak load usage time to the Smart Grids. Light weight and fast computing TEA algorithm is implemented for the data security. More importantly, our formal verification using the C tool and implementation on an ARM Cortex M0 Microcontroller confirms our claim using lab view at server side.
Vol 2, No 2 (2017): Modelling, Simulation and Analysis of the Thyristor-Controlled Series Capacitor (TCSC)
Author:Â Bhakti S Nitve
Abstract:Â The analysis presents the study of TCSC device on Simulink. TCSC is one of the important members of FACTS family that is rapidly increasingly and is applied for long transmission lines by the utilities in modern power systems to improve the power quality of the system. It can have various roles in the operation and control of power systems, such as scheduling power flow; decreasing unsymmetrical components; reducing net loss; providing voltage support; limiting short-circuit currents; mitigating sub synchronous resonance; damping the power oscillation and enhancing transient stability control of power systems, procedures are used to compensate dynamically the detrimental effect of nonlinear loads. The compensation process should be carried out without important alteration of the signal quality along with some benefits like reduction of losses in distribution lines, harmonic content minimization and power factor improvement. The simulation results demonstrate the performance of the system for TCSC FACTS device in improving the power profile and thereby voltage stability of the same. All simulations have been carried out in MATLAB/SIMULINK environment.
Vol 2, No 2 (2017): Comparative Study of Bi Directional Converters Used In Grid Interactive Small Scale Renewable Power System
Authors:Â Prakash Kerur, R. L. Chakrasali
Abstract:Â As the population increases and people continue to demand a higher standard of living, the demand for energy also continues to increase. Thus there is a rapid growing interest in renewable energy, such as fuel cells and photovoltaic systems in the distributed power system architecture. Innovative topologies for renewable energy conversion systems that integrate with electric grids and energy storage systems are being proposed, each with limited modes of operation for the various needs in smart grid applications. In the view of this, bidirectional power flow plays vital role in grid connected systems. In vehicleto-grid (V2G) systems, electric vehicles interact with the grid as distributed energy storage systems that offer many potential benefits. As an energy Interface between a vehicle and the grid, the bidirectional converter plays a crucial role in their interaction. Its reliability, safety, cost, efficiency, weight, size, harmonics, and other factors are of essential importance for V2G realization, especially for on-board operations. Beyond the common existing topologies for bidirectional converter, this paper brings out a comparative study of different types of bidirectional converter which are used in grid connected systems with highlighting the features of each converter for rooftop solar generation and hybrid power system in small scale renewable generation.
Vol 2, No 1 (2017): Batch Process with CIP
Authors:Â Prerana Kshirsagar, Manaswini Patil, Avinash Jayebhaye, Nisha Dagade
Abstract: This paper deals with automation in industrial plants where batch processes are used, such as food, pharmaceutical and cement industries. Individual pieces of equipment in these plants are controlled by independent programmable logical controllers (PLC). PLC-s communicates with each other and synchronizes their work. With a well-designed automated system, the need for operators’ supervision is greatly minimized and hence permits the labor cost to be reduced and optimizing the repeatability and efficiency of the process done by the system. Thus, the operator may readily and efficiently take real time action on the flow of the process permitting the latter to have an upper hand on the system as the latter may decide his own desirable set points at critical intervals. Clean-in-plant (CIP) processes are time intensive and waste large amounts of energy, water, and chemicals. New innovations in CIP technology allow plant operators to cut costs in an earth-friendly manner while still conforming to regulatory safety standards. This paper explains how new CIP technologies can improve production efficiency.
Vol 2, No 1 (2017): Planning & Development of SCADA Based Power Distribution System
Authors:Â Govind Rai Goyal, Mohit Kumar Jain
Abstract: Smart Grid is sophisticated, digitally enhanced power systems where the use of modern communications and control technologies allows much greater robustness, efficiency and flexibility than today’s power systems. A smart grid impacts all the components of a power system especially the distribution level. One subset of smart grids is smart metering / advanced metering infrastructure (AMI) etc. In a smart grid, all the various nodes need to interconnect to share data as and where needed. Smart Grid envisages providing choices to each and every customer for deciding the timing and amount of power consumption based upon the price of the power at a particular moment of time, apart from providing choices to the consumer and motivating them to participate in the operations of the grid, causing energy efficiency and accommodating all generation and storage options, Smart Grid also envisages various properties for the Grid like self-healing and adaptive The suite of Smart Grid products and technologies help maximizing system uptime, while also helping the utility more quickly to restore power to homes and businesses in the event of an outage. Government of India has recently formed “Smart Grid Forum†and “Smart Grid Task Force†for enablement of smart grid technology into Indian Power Distribution Utilities as a part of their Smart Grid initiative to meet their growing energy demand in similar with the developed country like USA, Europe etc.
2016
Vol 1, No 1 (2016): PSO Optimized Back Propagation Control Algorithm for Power Quality Enhancement Problem
Abstract:Â This paper presents an implementation of a three phase distribution static compensator (DSTATCOM) using a PSO Optimized back propagation (BP) control algorithm for its functions such as harmonic elimination, load balancing and reactive power compensation for power factor correction, and zero voltage regulation under nonlinear loads. A PSO Optimized BP-based control algorithm is used for the extraction of the fundamental weighted value of active and reactive power components of load currents which are required for the estimation of reference source currents. A prototype of DSTATCOM is developed using a digital signal processor, and its performance is studied under various operating conditions. The performance of DSTATCOM is found to be satisfactory with the proposed control algorithm for various types of loads.